​14 most important features of high reliability PCB

Whether it is in the manufacturing assembly process or in actual use, it is essential that the PCB has reliable performance. In addition to the associated costs, defects in the assembly process may be carried into the final product by the PCB, and failure may occur during actual use, resulting in a claim. Therefore, from this point of view, it is no exaggeration to say that the cost of a good quality PCB is negligible.

In all market segments, especially those that produce products in critical applications, the consequences of such failures are unimaginable.

These aspects should be kept in mind when comparing PCB prices. Although the initial cost of a reliable, guaranteed, and long-life product is high, it is worth the money in the long run.

1.25 micron hole wall copper thickness

Benefit

Enhanced reliability, including improved z-axis resistance to expansion.

Risk of not doing so

Blowing or degassing, electrical connectivity problems during assembly (inner layer separation, hole wall fracture), or failure under load conditions in actual use. IPCClass2 (the standard used in most plants) requires 20% less copper plating.

2. No welding repair or open circuit repair

Benefit

Perfect circuit ensures reliability and safety, no maintenance, no risk

Risk of not doing so

If it is not repaired properly, it will cause the board to open. Even if the repair is 'proper', there is a risk of failure under load conditions (vibration, etc.), which may cause malfunction in actual use.

3. Exceeding the cleanliness requirements of the IPC specification

Benefit

Improve PCB cleanliness to increase reliability.

Risk of not doing so

Residues and solder deposits on the board pose a risk to the solder mask. Ion residues can cause corrosion and contamination risks on the solder surface, which can lead to reliability issues (bad solder joints/electrical faults) and ultimately increase the actual fault occurrence. Probability.

4. Strictly control the service life of each surface treatment

Benefit

Solderability, reliability, and reduced risk of moisture intrusion

Risk of not doing so

Due to metallographic changes in the surface treatment of old boards, soldering problems may occur, and moisture intrusion may cause delamination, separation of inner layers and walls (opening) during assembly and/or actual use.

5.Use internationally renowned substrates – do not use “local” or unknown brands

Benefit

Improve reliability and known performance

Risk of not doing so

Poor mechanical properties mean that the board does not perform as expected under assembly conditions. For example, high expansion performance can cause delamination, open circuit, and warpage problems. Impaired electrical characteristics can result in poor impedance performance.

6. Cladding tolerance meets IPC4101 Class B/L requirements

Benefit

Strict control of the thickness of the dielectric layer can reduce the expected deviation of electrical performance.

Risk of not doing so

Electrical performance may not meet the specified requirements, and the output/performance of the same batch of components will vary greatly.

7. Define the solder mask material to ensure compliance with IPC-SM-840 ClassT requirements

Benefit

NCAB Group recognizes "excellent" inks for ink safety and ensures solder mask inks meet UL standards.

Risk of not doing so

Inferior inks can cause adhesion, flux resistance and hardness problems. All of these problems can cause the solder mask to detach from the board and eventually lead to corrosion of the copper circuit. Poor insulation properties can cause short circuits due to unexpected electrical connectivity/arc.

8. Define tolerances for shapes, holes and other mechanical features

Benefit

Strict control of tolerances can improve the dimensional quality of the product – improved fit, shape and function

Risk of not doing so

Problems during assembly, such as alignment/mating (the problem of press-fitting the needle is only found when the assembly is complete). In addition, there is a problem in mounting the base due to an increase in dimensional deviation.

9. The NCAB specifies the thickness of the solder mask, although there is no relevant regulation in the IPC.

Benefit

Improve electrical insulation properties, reduce the risk of flaking or loss of adhesion, and enhance the ability to withstand mechanical impact – no matter where the mechanical impact occurs!

Risk of not doing so

Thin solder masks can cause adhesion, flux resistance and hardness problems. All of these problems can cause the solder mask to detach from the board and eventually lead to corrosion of the copper circuit. Poor insulation properties due to the thin solder mask layer can cause short circuits due to accidental conduction/arc.

10. Define appearance requirements and repair requirements, although IPC is not defined

Benefit

Care and careful care in the manufacturing process to create safety.

Risk of not doing so

A variety of scratches, minor injuries, repairs and repairs – the board can be used but not good looking. In addition to the problems that the surface can see, what are the invisible risks, the impact on assembly, and the risks in actual use?

11. Requirements for plug depth

Benefit

High quality plug holes will reduce the risk of failure during assembly.

Risk of not doing so

The chemical residue in the immersion gold process may remain in the hole that is not filled with the plug hole, thereby causing problems such as solderability. Moreover, tin beads may be hidden in the holes, and the solder balls may splash out during assembly or actual use, causing a short circuit.

12. PetersSD2955 specified peelable blue plastic brand and model

Benefit

The designation of peelable blue glue can avoid the use of "local" or cheap brands.

Risk of not doing so

Inferior or inexpensive peelable glue may foam, melt, crack or solidify like concrete during assembly, so that the peelable glue cannot be peeled off/inactive.

13. The .NCAB performs specific approval and order procedures for each purchase order.

Benefit

The execution of this program ensures that all specifications have been confirmed.

Risk of not doing so

If the product specifications are not carefully confirmed, the resulting deviation may not be discovered until assembly or final product, and it is too late.

14. Do not accept sets of boards with scrapped units

Benefit

Not using partial assembly can help customers improve efficiency.

Risk of not doing so

A defective assembly requires special assembly procedures. If the x-out is not clearly marked or is not isolated from the panel, it is possible to assemble the known bad plate. Waste parts and time.